Bienvenue sur AUTOSON V 4.0


C'est à cause d'eux :
Guillaume (McJeanGui), Thomas (Scherenne), Guillaume, Thierry, Nicolas, Jérémy (dje), Richard (Richard), Michel (airdevin), Benjamin (kdb26), Olivier.
Que vous allez encore nous subir pendant 3 ans.

Merci aux généreux donateurs de la cagnotte v2.

signat

Que des vieux trucs !
greg
MEDIUM
MEDIUM
Messages : 429
Enregistré le : jeu. févr. 12, 2009 12:34 am

signat

Messagepar greg » mar. mars 04, 2014 4:00 pm

bonjour a tous et toutes

bon je voulais revenir sur la gamme signat
donc gamme signat rap roc rom ram lag log ont ni comprend rien :lol:
les noms avec des "o" sont les bas de gamme et donc avec les "A" les hauts de gamme
Déjà ont i verra plus claire donc
le ROC bas de gamme la RAP au dessus

donc voici les gammes dans l'ordre croissant:

ROC entrée de gamme
Dedans il y à ROC1 ROC2 ROC 3 ect ...selon le nombre de canaux
(Attention dedans vous avez des versions qui fonctionnent sur 24 volt
Pour les camions voir compatible 12volt)

RAP entrée de gamme un peut mieux
pareil RAP1 RAP2 ect.. selons le nombre de cannaux
(Attention dedans vous avez des versions qui fonctionnent sur 24 volt
Pour les camions voir compatible 12volt)

ROM milieu de gamme
rom1 rom2 rom3 non c'est pas les roumains :lol:

RAM les plus connu (meilleur que ROM )
Attention vous aves des versions avec carte mère doré et des versions carte mère classique en fait il s’agit des même amplis mais version économique comme les PS3 et PS3 fat
Exemple il y a des RAM2 version1 avec les connexions hp blanche voir photo
http://amp-performance.de/1150-Signat-Ram-2.html
et le RAM 2 version 2
http://amp-performance.de/346-Signat-Ram-2-MKII.html

Puis le série LAB haut de gamme ventilé même architecture que les LOG1 et 2 mais plus récent

la série LOG1 et 2 haut de gamme très imposant en taille (80x65x15cm ) par rapport au LAB

et la série FLAG introuvable et encore plus imposant

Et aussi des série class D les DIG1 et 2
Le RAMBO qui est en fait deux RAM assemblé
Et il existe d’autre ampli qui sorte encore aujourd’hui mais aucun avis sur leurs qualités

Acheter un signat d’occasion :
-vérifier que toutes les connexions ont leur vis
-vérifier la version 24volt / slim
-vérifier les vis du châssis sur les cotés elles ont tendance à partir avec les vibrations
-vérifier les RCA sur les RAM par exemple si ont vis trop fort l’écrou qui tient le RCA il se dessoude de la carte mère

voila vous serez tous sur le sizg sizg
2.21 gggigggo waattt maiss c'esttt unn amplli fussioon temmporel que tuuu à laaa moonn dieuu

Avatar de l’utilisateur
Ewen
Vétéran Autoson
Vétéran Autoson
Messages : 2655
Enregistré le : dim. août 24, 2008 1:53 am
Localisation : bretagne

Messagepar Ewen » mar. mars 04, 2014 6:25 pm

F L A G

Once upon a time...

A dream grows into idea, the idea grows into a concept.
Years of experience, ability and know-how grow into a product.

Introducing the FLAG amplifier in 1994, probably the most powerfull series-built amplifier ever constructed for mobile purposes, SIGNAT succeeded in creating an extreme highlight - the absolute reference!

The professional press was stunned: "absolute top class", "reference", "never seen before".

The blue ´space ship´ with its impressive design, with a total power of 3200 Watts introduced a standard. We claim it is unequalled up to now.

With its massive performance the FLAG develops an amplifying capacity whish reproduces the original music recording so faithfully that a better achievement is unthinkable. Without any distortion, without any colouring. The FLAG brings out the bass frequencies with endless power, extremely deep, extremly pure. The midrange frequencies are crystal-clear. This is what it is all about.
FLAG and the slightly smaller models LOG 1 and LOG 2 are mechanically developed and designed by Backes&Mueller, best-known high-end architect of active loudspeakers.

Now, at the threshold of the new millenium, the time has come for SIGNAT to set another new standard, voluable for centuries to go.
In the same way as the nineties started off with FLAG and LOG, the new SIGNAT modular amplifier system will announce a new car hifi millenium. Like their predecassors these amplifiers are designed and developed by Backes&Mueller, a guarantee for the finest technology, unequalled performance and audiophile listening experience.


Image

ImageImage




LAB Series

Like the legendary amplifiers FLAG and LOG, the new LAB amplifiers have been develped by the high-end goldsmiths BACKES & MULLER. And once again the aimed at an uncompromising concept to keep up the possibility of ` natural and distortioin freed reproduction of musical sound images´. The result is worth hearing!
This tremendous performance asked for an intelligent cooling strategy, in order to dissipate the developed heat in an adequate way and to secure a long lasting continiuous performance.
Besides the external coolingfins internal heat sinks at both sides take care of additional heat dissipating surface; besides that, they pave the way for the airflow of the dynamic cooling components.
At each side of the profile a cooling fan prevents overheating of the performing components. The speed of both fans is controlled, depending on the heat heat development of the device; mthe SCF electronic circuit detects the heat development with sensors and starts the fans from a temperature of about 40 degrees Celsius. If necessary their speed will be increased.

Backlit control panel
SCF fan cooling system
FCC Frequency Compensation Control
ADS Anti Distorsion System
Incl. BRS Bass Remote Control for 1 pair of channels.

The techical equipment of the LAB models leaves nothig to be desired. Active high and low pass filters offer an extreme variety of programming adjustments, which will respopnd to individual demands and wishes of any form; fully active operation without external crossovers - no problem! A combination of high and low pass allows for a crossover with bandpass behaviour. The extremly steep subsonic filter with a variable crossover point quarantees the highest efficiency. In this way the deepest frequency parts are eliminated and unnecessary, excessive strain on the loudspeakers by subsonic frequency is prevented. Top of the bill in filtering issues is the FCC. The overall difficult problem of droning, a tipical caraudio specific problem, is the gist of the metters. FCC immediately intervenes whenever the droning effects gets annoying. In the critical frequency range it is possible to intervene manually in order to smooth effectively the inadequate boost caused by the acoustic behaviour of the vehicle´s interior.

Lit up control panel
SCF fan cooling system
FCC Frequency Compensation Control
ADS Anti Distortion System
Incl. BRC Bass Remote Control

The phase shift control directly influences the phase angle of the output signal; in principle the phase can be shifted continiously from 0 to 360 degrees. In this way timing problems caused by the different loudspeaker locations in the vehicle can be solved very elegantly

An anti-distorsion system ADS not only takes care of an excellent loudspeaker protection; the electronic circuit constantly guards the output signal in order to recognise eventualyy occuring distortions right from the start and to adjust if necessary. In other words: also at the limits ADS prevents the tipical `clipping´ of the output signal (which often leads to a fatal damage of the loudspeaker). Even the sound is clear and clean.

With every LAB amplifier comes a compact BRC ( bass remote control). Whenever a subwoofer has been applied, the bass level can be reduced or increased with the BRC from behind the steering wheel. Bass differences in hte sources ( CD, cassette) or in hte recordings can easily and individually be compensated.

Before a LAB amplifier leaves the factory, it is subject to an extensive trial procedure. Every single LAB amplifier comes with an individual testing report, which states the important measuring data and certifies the operating capability of the device.




LAB 2

Image

Amplificateur 2 canaux
Puissance : 2x 100 (4 ohm, THD = 0.05%)
Puissance : 1x370W (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 70KHz
Filtre passe-bas : 40-200Hz, 24dB / 600-6000, 12dB
Filtre passe-haut : 10-50Hz, 24dB / 60-600Hz, 12dB
Contrôle de la phase en continu : 10 - 340°
Système de ventilation intégré et autogéré
Contrôle du niveau du sub à distance
Dimensions : 330 x 70 x 350


Specification data:
Amp type: 2 channel
Pc board: double sided gold-plated 24 K
Power terminal: platinum plated fully isolated type
Speaker terminals: platinum plated fully isolated type
Signal input terminals: 4 x RCA jacks platinum plated
BIC balanced input circuity
ENS Electronic Noise
Bridged mode: yes (min. 2 Ohm)
Protection and control circuites: Temperature, overload, short circuit,
DC offset, +/-reverse, low/high voltage
Output load impendance (stereo mode): 1 - 8 Ohm
Active low pass filter: 40-200Hz, 24dB; 600-6000Hz, 12dB
Active high pass filter: 10-50Hz,24dB; 60-600Hz,12dB; 2-10Hz,12dB
Phase control: 10ş-340ş shift
Remote control: BRC type (LPF on)
Technical data:
RMS power at 4 Ohm (0,05% THD): 2x100W
RMS power at 4 Ohm, bridged (0,1% THD): 1x370W
RMS power at 2 Ohm (0,2% THD): 2x185W; 1x550W bridged
RMS power at 1 Ohm (0,2% THD): 2x280W
S/N ratio (A-weighted): 106 dB
Freq. response (-3dB): 10-70 kHz
Stereo separation: 70 dB
Input sensitivity: 100mV - 5V
Input impendance: 30 kOhm
Fuse rate: 2 x 40A (maxi)
Supply voltage: 12 V DC
Dimensions: 330 x 70 x 350 mm

1075€

LAB 4

Image

Amplificateur 4 canaux
Amplificateur 2 canaux
Puissance : 4x100 (4 ohm, THD = 0.05%)
Puissance : 2x370W (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 70KHz
Filtre passe-bas : 40-200Hz, 24dB / 600-6000, 12dB
Filtre passe-haut : 10-50Hz, 24dB / 60-600Hz, 12dB
Contrôle de la phase en continu : 10 - 340°
Système de ventilation intégré et autogéré
Contrôle du niveau du sub à distance
Dimensions : 330 x 70 x 500



Specification data:
Amp type: 4 channel
Pc board: double sided gold-plated 24 K
Power terminal: platinum plated fully isolated type
Speaker terminals: platinum plated fully isolated type
Signal input terminals: 2 x RCA jacks platinum plated
BIC balanced input circuity
ENS Electronic Noise
Bridged mode: yes (min. 2 Ohm)
Protection and control circuites: Temperature, overload, short circuit,
DC offset, +/-reverse, low/high voltage
Output load impendance (stereo mode): 1 - 8 Ohm
Active low pass filter: 40-200Hz, 24dB; 600-6000Hz, 12dB
Active high pass filter: 10-50Hz,24dB; 60-600Hz,12dB; 2-10Hz,12dB
Phase control: 10ş-340ş shift
Remote control: BRC type (LPF on)
Technical data:
RMS power at 4 Ohm (0,05% THD): 4x100W
RMS power at 4 Ohm, bridged (0,1% THD): 2x370W
RMS power at 2 Ohm (0,2% THD): 4x185W; 2x500W bridged
RMS power at 1 Ohm (0,2% THD): 4x250W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-70 kHz
Stereo separation: 70 dB
Input sensitivity: 100mV - 5V
Input impendance: 30 kOhm
Fuse rate: 2 x 60A (maxi)
Supply voltage: 12 V DC
Dimensions: 330 x 70 x 500 mm

1337€


Bass Remote Control

Image



RAM Series



SIGNAT amplifiers of the RAM MARK II and ROC series have been developed according to the American concept; the audiophile fine-tuning was executed by SIGNAT in co-operation with the engineers of Backes & Mueller. The result is fantastic: units designed with great accuracy and excellent finish. In order to withstand extreme in-car conditions such as vibrations and shocks, the RAM amplifiers have been equipped with double-sided PC boards, strenghtened by glassfibre. This techique, together with a neat layout of the PC board, ensures a reliable operation.
All SIGNAT amplifiers feature an outstanding finish and use high-quality components.
The RAM power amplifiers come with low-distortion bipolar technique, operating in dynamic class A-mode. Due to this special principle, tri-mode and bridged operationare possible without the need of an additional switch. The amplifiers are protected by effective monitoring and protection circuitry; in case of a short circuit, thermal or electric overload, the amplifier is muted immediatly and can omly be operated again when normal conditions prevail. The speaker output terminals are protected by DC offset. 24 carat gold plating of the PC boards minimizes possible transmission losses. All conductors are protected against corrosion.

High-performance, carefully selected components, and an exact and detaild finishing guarantee an optimum sound performance. Both speaker and power terminals are 24 carat gold-plated, ensuring a signal trnasmission absolutely free of losses. The terminals are enclosed in plastic to avoid shorting; the extremely stable srew terminals accept cabels up to 20 mm2 cross-section.
The Press

Test: hifi mobil RAM MARK II

Value money ***
... the RAM 2 is excellently finished and offers all the possibilities of a 4-channel amplifier. All channel come with both low and high pass filters..... the SIGNAT amplifier can be strongly recommended to anybody who is looking for a very powerfull amplifier.´´

Second order active electronic crossovers order active electronic crossovers (with a 12 dB/oct slope) ensure a perfect sound adaption to your speaker systems.
Low pass or high pass configuration can be selected; the cut-off frequencies of all filters are continuously variable between 50 and 250 Hz. Voltage supply is granted by super fast power-MOSFET transistors; the effective switching power supplies guarantee maximum performance with minimum heat development. Every RAM MARK II amplifier features separate high-power supplies, reducing the mutual influencing of the amplifiers to a minimum. Due to the extremy stable power supply, RAM MARK II amplifiers tolerate impendances down to 1 Ohm. Thanks to the super fast pre-amplifiers with a high voltage/noise-ratio the RAM MARK II amplifiers offer outstanding dynamics and transparency.



RAM 1 MKII



Image

Amplificateur 6 canaux
Puissance : 2x 90 + 4x 45W (4 ohm, THD = 0.05%)
Puissance : 1x235 + 2x 110W (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 65KHz
Filtre passe-bas : 50-250Hz, 12dB/octave (ch 5/6)
Filtre passe-haut : 50-250Hz, 12dB/octave (ch 1/2 et 3/4)
Dimensions : 230 x 57 x 432


pecification data:
Amp type: 6 channel
Pc board: double sided gold-plated 24 K
Power terminal: gold plated fully isolated type
Speaker terminals: gold plated fully isolated type
Signal input terminals: 6 x RCA jacks gold plated
BIC balanced input circuity
Bridged mode: yes (min. 2 Ohm)
Trimode operation: built in
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 1 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch 5/6)
Active high pass filter: 50-250Hz,12dB (ch 1/2 & 3/4)
Technical data:
Max. peak music power: 700W
RMS power at 4 Ohm (0,05% THD): 2x90W + 4x45W
RMS power at 4 Ohm, bridged (0,1% THD): 1x235W + 2x110W
RMS power at 2 Ohm (0,2% THD): 2x120W + 4x60W
RMS power at 1 Ohm (0,2% THD): 2x120W + 4x60W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-65 kHz
Stereo separation: 70 dB
Input sensitivity: 100mV - 4V
Input impendance: 20 kOhm
Fuse rate: 2 x 30A
Supply voltage: 12 V DC
Dimensions: 230 x 57 x 432 mm

593€


RAM 2 MKII

Image

Amplificateur 4 canaux
Puissance : 4x 90 (4 ohm, THD = 0.05%)
Puissance : 2x230 (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 65KHz
Filtre passe-bas : 50-250Hz, 12dB/octave (ch av/ar)
Filtre passe-haut : 50-250Hz, 12dB/octave (ch av/ar)
Dimensions : 230 x 57 x 370


Specification data:
Amp type: 4 channel
Pc board: double sided gold-plated 24 K
Power terminal: gold plated fully isolated type
Speaker terminals: gold plated fully isolated type
Signal input terminals: 4 x RCA jacks gold plated
BIC balanced input circuity
Bridged mode: yes (min. 2 Ohm)
Trimode operation: built in
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 1 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch front & rear)
Active high pass filter: 50-250Hz,12dB (ch front & rear)
Technical data:
Max. peak music power: 650W
RMS power at 4 Ohm (0,05% THD): 4x90W
RMS power at 4 Ohm, bridged (0,1% THD): 2x230W
RMS power at 2 Ohm (0,2% THD): 4x120W
RMS power at 1 Ohm (0,2% THD): 4x120W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-65 kHz
Stereo separation: 70 dB
Input sensitivity: 100mV - 4V
Input impendance: 20 kOhm
Fuse rate: 2 x 30A
Supply voltage: 12 V DC
Dimensions: 230 x 57 x 370 mm

465€


RAM 3 MKII

Image

Amplificateur 2canaux
Puissance : 2x 150 (4 ohm, THD = 0.05%)
Puissance : 1x450 (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 65KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave
Dimensions : 230 x 57 x 300


Specification data:
Amp type: 2 channel
Pc board: double sided gold-plated 24 K
Power terminal: gold plated fully isolated type
Speaker terminals: gold plated fully isolated type
Signal input terminals: 2 x RCA jacks gold plated
BIC balanced input circuity
Bridged mode: yes (min. 2 Ohm)
Trimode operation: built in
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 1 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch 1/2)
Active high pass filter: 50-250Hz,12dB (ch 1/2)
Line output: 2 x RCA jacks gold plated, full range
Technical data:
Max. peak music power: 500W
RMS power at 4 Ohm (0,05% THD): 2x150W
RMS power at 4 Ohm, bridged (0,1% THD): 1x450W
RMS power at 2 Ohm (0,2% THD): 2x230W
RMS power at 1 Ohm (0,2% THD): 2x240W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-65 kHz
Stereo separation: 70 dB
Input sensitivity: 100mV - 4V
Input impendance: 20 kOhm
Fuse rate: 2 x 30A
Supply voltage: 12 V DC
Dimensions: 230 x 57 x 300 mm

353€






DIG Series



Subwoofers deserve special treatment when it comes to amplification, because the low frequency range has its own characteristic properties. The SIGNAT DIG 1 class D amplifier technology is perfectly fit for `power-hungry´ subwoofers
The extremly high efficiency (more then 80%!) allows for an incredibly powerful performance, even at impendences as low as 1 Ohm, while the heat sink can stay relativly small.
The 24k gold plated PC board ensures an excellent conductivity; there`s no chance for corrosion to deteriorate the sound quality. The BIC signal inputs (Balanced Input Technology) with `floating ground´ guarantee insensitivity against unwanted external interference.

The SIGNAT DIG 1 boasts several other typical subwoofer characteristics, like the phase shift, variable low pass crossover with Q-factor control and a subsonic crossover, which effectively filters out the lowest frequencies: these frequencies only waste amplifier power, while they can damage the subwoofer. Furthermore, the subwoofer level can be adjust from the driver`s seat by means of the convenient remote control of the DIG 1, attractively shaped as a little amplifier.

DIG 1

Image

Amplificateur mono numérique
Puissance : 1x 430W (4 ohm, THD = 0.5%)
Bande passante : 5Hz - 250Hz
Filtre passe-bas : 30-250Hz, 18dB/octave
Filtre passe-haut : 10-30Hz, 18dB/octave (subsonic)
Contrôle de la phase en continu : 0-180°
Dimensions : 248 x 55 x 300 mm


Specification data:
Amp type: 1 channel monoblock for subwoofer
Pc board: double sided gold-plated 24 K
Power terminal: gold plated fully isolated type
Speaker terminals: gold plated fully isolated type
Signal input terminals: 6 x RCA jacks platinum plated
BIC balanced input circuity
Bridged mode: monoblock
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 1 - 8 Ohm
Active low pass filter: 30-250Hz 18dB
Active high pass filter: 10-30Hz 18dB (subsonic)
Q-factor control: 0,5 - 1,2 for LPF
Phase control: 0ş-180ş
High level input
Line output: 2 x RCA jacks gold plated, full range
Remote control: BRC type
Technical data:
RMS power at 4 Ohm (0,05% THD): 1x430W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 5-250 kHz
Input sensitivity: 300mV - 5V
Input impendance: 25 kOhm
Fuse rate: 2 x 40A
Supply voltage: 12 V DC
Dimensions: 248 x 55 x 300 mm

625€


DIG 2 200

Image

Amplificateur 2 canaux numérique large bande
2 x 100W (4 ohm, THD = 0.05%)
2 x 170W (2 ohm, THD = 0.2%)
1 x 350W (4 ohm, THD = 0.1%)
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave
Filtre subsonique : 20Hz, 18dB/octave
Commande déportée du niveau des basses
Dimensions : 230 x 31 x 314 mm

608€


DIG 2 400

Image

Amplificateur 2 canaux numérique large bande
2 x 180W (4 ohm, THD = 0.05%)
2 x 310W (2 ohm, THD = 0.2%)
1 x 600W (4 ohm, THD = 0.1%)
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave
Filtre subsonique : 20Hz, 18dB/octave
Commande déportée du niveau des basses
Dimensions : 230 x 31 x 355 mm

720€


Bass Remote Control

Image




ROM Series


ROM amplifiers boast outstanding equipment and fascinating technoques! These SIGNAT amps completely stand out from the average and not just because of their exclusive physical apperance. Their output power and well-considered features are very seductive too; adjustable active crossovers allow for an optimised adaption to your loudspeaker system, steep subsonic filters avoid unneccessary strain.

The three- and five channel ROM models feature 2 Ohm stable subwoofer (mono) channels. Optionally a SIGNAT BRC bass controlled can be installed.

BRC Bass Remote Control, this compact control (whith the exterior of a little amplifier) makes it easy to adjust the bass level comfortably from behind the steering wheel. For example to smooth bass-predominant recordings or on the other hand to boost the bass purpose. The volume of the subwoofer can be varied from -6dB to +6dB, starting form the basic settings of the input sensitivity; thus the bass level can be adapted to any chosen music source ( CD, cassette).

Naturally all ROM Amplifier come with SIGNAT BIC (balanced input circuity) inputs and the proven ENS (electronic noise suppression) system in order to guarantee the utmost reduction of unwonted noises.


ROM 2

Image

Amplificateur 2 canaux
Puissance : 2x110W (4 ohm, THD = 0.05%)
Puissance : 1x350W (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 60KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave
Dimensions : 242 x 60 x 285


Specification data:
Amp type: 2 channel
Pc board: double sided
Power terminal: gold plated screw type
Speaker terminals: gold plated screw type
Signal input terminals: 2 x RCA jacks gold plated
BIC balanced input circuity
ENS Electronic Noise Suppression
Bridged mode: yes (min. 4 Ohm)
Trimode operation: built-in
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 2 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch 1/2)
Active high pass filter: 50-250Hz,12dB (ch 1/2 )
Line output: 2 x RCA jacks gold plated, full range
Technical data:
Max. peak music power: 360W
RMS power at 4 Ohm (0,05% THD): 2x110W
RMS power at 4 Ohm (0,1% THD): 1x350W
RMS power at 2 Ohm (0,2% THD): 2x175W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-60 kHz
Stereo separation: 70 dB
Input sensitivity: 150mV - 5V
Input impendance: 25 kOhm
Fuse rate: 2 x 20A
Supply voltage: 12 V DC
Dimensions: 242 x 60 x 285 mm

319€


ROM 3

Image

Amplificateur 3 canaux
Puissance : 1x125 + 2x 60 (4 ohm, THD = 0.05%)
Puissance : 1x180 + 2x90 (2 ohm, THD = 0.2%)
Bande passante : 10Hz - 60KHz
Filtre passe-bas : 50-250Hz, 12dB/octave (ch sub)
Filtre passe-haut : 50-250Hz, 12dB/octave (ch 1/2)
Subsonic : 20Hz, 18dB/octave
Dimensions : 242 x 60 x 310


Specification data:
Amp type: 3 channel
Pc board: double sided
Power terminal: gold plated screw type
Speaker terminals: gold plated screw type
Signal input terminals: 4 x RCA jacks gold plated
BIC balanced input circuity
ENS Electronic Noise Suppression
Bridged mode: yes (min. 4 Ohm)
Trimode operation: -
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 2 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch sub)
Active high pass filter: 50-250Hz,12dB (ch 1/2 ). 20Hz, 18dB subsonic
Remote control: option
Technical data:
Max. peak music power: 400W
RMS power at 4 Ohm (0,05% THD): 1x125W + 2x60W
RMS power at 2 Ohm (0,2% THD): 1x180W + 2x90W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-60 kHz
Stereo separation: 70 dB
Input sensitivity: 150mV - 5V
Input impendance: 25 kOhm
Fuse rate: 2 x 25A
Supply voltage: 12 V DC
Dimensions: 242 x 60 x 310 mm

335€


ROM 4

Image

Amplificateur 4 canaux
Puissance : 4x90 (4 ohm, THD = 0.05%)
Puissance : 2x240 (4 ohm, ponté, THD = 0.1%)
Bande passante : 10Hz - 60KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave
Dimensions : 230 x 60 x 390


Specification data:
Amp type: 4 channel
Pc board: double sided
Power terminal: gold plated screw type
Speaker terminals: gold plated screw type
Signal input terminals: 4 x RCA jacks gold plated
BIC balanced input circuity
ENS Electronic Noise Suppression
Bridged mode: yes (min. 4 Ohm)
Trimode operation: built in
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 2 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch 1/2 & 3/4)
Active high pass filter: 50-250Hz,12dB (ch 1/2 & 3/4)
Technical data:
Max. peak music power: 600W
RMS power at 4 Ohm (0,05% THD): 4x90W
RMS power at 4 Ohm (0,1% THD): 2x240W
RMS power at 2 Ohm (0,2% THD): 4x125W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-60 kHz
Stereo separation: 70 dB
Input sensitivity: 150mV - 5V
Input impendance: 25 kOhm
Fuse rate: 2 x 30A
Supply voltage: 12 V DC
Dimensions: 242 x 60 x 390 mm

400€


ROM 5

Image

Amplificateur 5 canaux
Puissance : 4x70 + 1x180W (4 ohm, THD = 0.05%)
Puissance : 4x90 + 1x300 (2 ohm, THD = 0.1%)
Bande passante : 10Hz - 60KHz
Filtre passe-bas : 50-250Hz, 12dB/octave (ch 1/2 et 3/4)
Filtre passe-bas canal sub : 50-150Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave (ch 1/2 et 3/4)
Dimensions : 240 x 60 x 450


Specification data:
Amp type: 5 channel
Pc board: double sided
Power terminal: gold plated screw type
Speaker terminals: gold plated screw type
Signal input terminals: 6 x RCA jacks gold plated
BIC balanced input circuity
ENS Electronic Noise Suppression
Bridged mode: yes (min. 4 Ohm)
Trimode operation: built in
Protection and control circuites: Temperature, overload, short circuit,
DC offset
Output load impendance (stereo mode): 2 - 8 Ohm
Active low pass filter: 50-250Hz, 12dB (ch 1/2 & 3/4) 50-150Hz, 12dB
(sub)
Active high pass filter: 50-250Hz,12dB (ch 1/2 & 3/4)
Line output: 2 x RCA jacks gold plated, full range
Active band pass filter ch 3/4: 50-250Hz, 12dB HPF - 100-500Hz, 12dB
LPF
Remote control: option
Technical data:
Max. peak music power: 850W
RMS power at 4 Ohm (0,05% THD): 1x180W + 4x70W
RMS power at 2 Ohm (0,2% THD): 1x300W + 4x90W
S/N ratio (A-weighted): 105 dB
Freq. response (-3dB): 10-60 kHz
Stereo separation: 70 dB
Input sensitivity: 150mV - 4V
Input impendance: 25 kOhm
Fuse rate: 2 x 40A
Supply voltage: 12 V DC
Dimensions: 242 x 60 x 450 mm

477€




SIGNAT RAP

RAP 1

Image

Amplificateur 5 canaux
Puissance : 4x55 + 1x150W (4 ohm, THD = 0.05%)
Bande passante : 10Hz - 55KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave

433€


RAP 2

Image

Amplificateur 4 canaux
Puissance : 4x70W (4 ohm, THD = 0.05%)
Bande passante : 10Hz - 55KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave

369€


RAP 3

Image

Amplificateur 3 canaux
Puissance : 2x40 + 1x100W (4 ohm, THD = 0.05%)
Bande passante : 10Hz - 55KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave

289€


RAP 4

Image

Amplificateur 2 canaux
Puissance : 2x75W (4 ohm, THD = 0.05%)
Bande passante : 10Hz - 55KHz
Filtre passe-bas : 50-250Hz, 12dB/octave
Filtre passe-haut : 50-250Hz, 12dB/octave

257€




Original SIGNAT LOG1 4 Kanal Endstufe
Designed by BACKES&MÜLLER (Backes & Müller)

Diese Endstufe markiert ein absolutes High-End Highlight.

4 Kanal High - End Verstärker,
Dauerausgangsleistung:

4 x 120 Watt an 4 Ohm,
4 x 155 Watt an 2 Ohm,
2 x 310 Watt an 4 Ohm gebrückt,

10 Hz - 100kHz

SIGNAT hat diese Amps von Backes&Müller, DER High-End Hifi-Schmiede als Fahrzeug-Verstärker entwickeln lassen.

Heraus kam die hier angebotene LOG1 als 4-Kanal Version, sowie die LOG2 als 2-Kanal Endstufe.



Diese Teile wurden dann in HANDARBEIT gebaut und abgeglichen. Die Fotos sprechen für sich, ebenso die Maße und Gewichte: Das Teil ist ca. 18kg schwer, ca. 65x45x15cm in den Abmessungen.

Vielfältige Schaltmöglichkeiten runden dieseses Prachtstück ab, so kann dieser Amp auch gebrückt als 3 oder 2-Kanel Endstufe gefahren werden.

Komplett mit Manual und Plexiglas-Scheibe für Show-Installationen!

Speziell für diese Verstärker mußten Hochleistungstransformatoren entwickelt werden, da die auf dem Markt angebotenen Typen zu schwach und zu wenig dauerbelastbar waren. Die Verkabelungsanschlüsse von der Stromleitungsseite fassen 60qmm. Eigens für diese Verwendung wurde ein Connectorblock konstruiert. Auch innen wird in großem Querschnitt gearbeitet. Die gesamte mechanische Konstruktion ist identisch mit der des FLAG, lediglich die "Lufthutzen", also die Ansaugstutzen des FLAG, werden hier nicht verwendet, sondern massive Flansche mit Lochdurchsatzstahlblechen zum Schutze des Lüfters einerseits und der Finger andererseits. Auch diese Geräte verfügen über eine elektonische Sicherung, die im Falle einer Überhitzung für den kontrollierten Eisatz der Lüfter sorgt und notfalls den gesamten Verstärker abschaltet.

Die Enstufen LOG 1 und LOG 2 sind kompromißlos wie ihr großer Bruder, der ultimative FLAG.

Auch diese beiden 4- und 2- Kanal Amplifier werden nach den gnadenlosen High-End-Ansprüchen von Backes & Müller gebaut.

In perfekter Ausführung, mit den besten Materialqualitäten und einem
Leistungsspektrum von 4 x 155 Watt (LOG 1) bzw. 2 x 200 W (LOG 2) an 2 Ohm
liefern diese beiden Endstufen in jedem Hochleistungs-Sound-System ihren Beitrag:
die naturgetreue, verfälschungsfreie Wiedergabe musikalischer Klangbilder in jedem einzelnen Frequenzbereich, mit präziser Reproduktion im Hoch- und Mitteltonbereich und machtvoller, fast brutaler Kraft für die Tieftöner.


Testbericht.: HiFi MOBIL 4/97 LOG 1
Kauftip, Referenzklasse
Preis / Leistung ****

"Alles ist so kräftig dimensioniert, als sei es für die Ewigkeit gebaut...
Und die LOG 1 legte sehr souverän los.
Ihr Klangbild entspricht dem eines sehr guten HIFI – Verstärkers aus dem Heimbereich, gewürzt mit einem autospezifischen Kickbass Plus sauberer, mächtiger Tiefe.
Unnötig zu sagen, daß die SIGNAT natürlich nicht verfärbte und Musik naturbelassen reproduzierte. Auch an der Räumlichkeit des Klangbilds gab es nichts auszusetzen...



Weitere Details auf der Herstellerseite von signat aus Österreich





rambo * Glasfaserverstärkte, doppelseitig kaschierte Leiterplatte
* Minimale Übertragungsverluste durch 24-Karat Hartgoldüberzug aller Leiterbahnen
* Ultrastabile Schaltnetzteile in MOSFET- Technologie mit 4 getrennten Leistungstransformatoren
* Dynamic Class-A Power-Endstufe in Bipolar-Technik
* 24-Karat-hartvergoldete RCA-Stecker, Lautsprecheranschlüsse, sowie Power Terminals
* 1 Ohm stabil
* Brückbar
* Tri-mode tauglich
* Soft Start
* Elektronische Schutzkreise: Thermische Überlastung, elektrische Überlastung, Kurzschluß und DC-Offset-Überwachung an den Lautsprecherklemmen
* Integrierte Frequenzweiche, regelbar:

Tiefpaß-Filter (12dB/Oct.), Frequenz variabel
Hochpaß-Filter (12dB/Oct.), Frequenz variabel
Full Range

* schaltbare Bass-Boost-Funktion +6dB
* Montagefreundliches Chassis-Design
* Betriebsspannung +12Volt DC, Minus an Masse

Max. Spitzen-Ausgangsleistung: 1150 Watt

RMS-Ausgangsleistung an 4 Ohm (THD=0,1%): 2 x 150 Watt + 4 x 85 Watt

RMS-Ausgangsleistung an 4 Ohm, gebrückt (THD=0,1%): 1 x 450 Watt + 2 x 230 Watt

RMS-Ausgangsleistung an 2 Ohm (THD=0,2%): 2 x 230 Watt + 4 x 120 Watt

RMS-Ausgangsleistung an 2 Ohm, gebrückt (THD=0,2%): 1 x 500 Watt + 2 x 280 Watt

RMS-Ausgangsleistung an 1 Ohm (THD=0,2%): 2 x 280 Watt + 4 x 160 Watt

Geräuschspannungsabstand (A-Filter): 105 dB A
Frequenzgang: 10 Hz - 50 kHz
Anstiegsgeschwindigkeit: 10 V / müsec
Stereo Kanaltrennung: 70 dB
Eingangsempfindlichkeit: 100 mV bis 4.0 V
Eingangsimpedanz: 20 kOhm
Dämpfungsfaktor: 200 / 300
Sicherungen: 4 x 30 A
Abmessungen B x H x T: 230 x 57 x 700 mm

Image
Image
Image
Image
Image
Image
Image
Ty Vito
Pio P99rs , A/D/S PH30.2 , Dayton RS28F , Scan 15W

Avatar de l’utilisateur
chris@i'go
MODO
MODO
Messages : 20446
Enregistré le : mar. févr. 22, 2011 7:01 pm
Localisation : 44 Nantes Les Bains/ Plage/ sur mer

Messagepar chris@i'go » mar. mars 04, 2014 7:08 pm

Merci les loulous

Je n y comprenais rien dans les gammes Signat

:)
"Old" inclusive

ffddrifter
AMPLI
AMPLI
Messages : 951
Enregistré le : mer. août 01, 2012 7:13 pm
Localisation : Wintzenheim 68
Contact :

Messagepar ffddrifter » lun. août 25, 2014 10:58 pm

Moi j'ai un petit Ram ii mk2 qui trônent toujours au milieu de mon coffre !

Très fiable comme ampli :D
Le savoir c'est comme la confiture, moins on en a, plus on l'étale.

Mennceros
TWEETER
TWEETER
Messages : 174
Enregistré le : jeu. janv. 02, 2014 1:26 pm
Localisation : Suisse

Re: signat

Messagepar Mennceros » mer. nov. 09, 2016 10:58 pm

Et concernant leur ancienne gamme Onyx, des avis ? :p


Retourner vers « TOUT L'ANCIEN  »

Qui est en ligne

Utilisateurs parcourant ce forum : Aucun utilisateur enregistré et 4 invités